The G-STRETCH 202 is a cost efficient solution, suitable for all the desired stretching process
Particular features
■ Pneumatic stretching system for all mesh types currently available on the market, capable of chieving stretching values of up to 60N.
■ Pneumatic stretching with highest precision/reproducibility
■ Cost-efficient entry-level model for automatic mesh stretching.
■ Modular extension possible in 250 mm/10“ increments p/side (warp + weft)
■ Stretching stroke per clamp 80 mm/3.1“.Total 160 mm/6.2“ in warp and weft direction
■ The simple and user-friendly control module with two separate regulator circuits for the X axis and the Y axis allows individual adjustment of the stretching force and of the stretching speed.
■ The pneumatic system guarantees an efficient work process. The desired stretching power must only be adjusted for the first screen of a series.
■ While the mesh is being stretched, the screen frame is prestressed with the same counter-stretching force.
■ During the stretching process, the pneumatic stretching clamps can be shifted sideways in order to compensate any extension of the mesh.
■ The width of a DUPLEX stretching clamp is 250 mm/10“. This ideal width enables every single stretching clamp to automatically compensate any mesh irregularities, which guarantees that the mesh is evenly stretched on its entire surface.
■ The frame saddle of each stretching clamp can be easily adjusted in 5mm/0.1“ increments to meet frame profile heights between 20mm/0.8“ and 55mm/2“.
■ During the stretching process the mesh is automatically pulled over the frame. Once the stretching process is completed, the mesh can be directly glued onto the frame.
■ In the event of mesh tearing, the retaining straps prevent the stretching clamps from bouncing back.
■ Ergonomical design and high-quality material such as special steel V2A and aluminium are standard features of the stetching clamps.
Option A
■ In the automatic mode, the system offers you totally 50 freely programmable programs. Upon selecting the program number, the automatic process is started by pressing the ENTER key.
■ Up to four stretching cycles are processed one after the other (stretching / resting time – stretching, etc.)
Option W
■ This option consists of a wooden board with either 4, 6 or 9 adjusting plates (to be selected) for CD screen frames. An angle graduation is engraved into the frames which allows a precise setting of the required value of the angle 0°, 7.5°,15° and 22,5°.
Single clamp
|
Maximum length
|
mm/inch
|
505/20"
|
|
Width
|
mm/inch
|
260/10"
|
|
Weight
|
kg
|
5.5
|
|
Stretching width
|
mm/inch
|
250/10"
|
|
Frame profile height
|
mm/inch
|
20-55/0.7"-2"
|
|
Clamp travel distance
|
mm/inch
|
80/3"
|
|
Maximum mesh tension
|
N
|
60
|
Control desk
|
Length
|
mm/inch
|
420/16.5"
|
|
Width
|
mm/inch
|
230/9"
|
|
Height (option A)
|
mm/inch
|
200 (400)/8" (16")
|
Connection value
|
Option A
|
230 Volt
|
50-60 Hz
|
Stretching pressure
|
X-axis and Y-axis
|
separately adjustable
|
|
Stretching speed
|
X-axis and Y-axis
|
separately adjustable
|
|
Compressed air
|
Connection value
|
Bar
|
9
|
|
Air consumption
|
|
|
|
per clamp
|
l/stroke
|
0.15
|
|
Compressor capacity
|
l/min
|
5-20
|